Home beauty devices are sold on flash count. Twenty thousand flashes, fifty thousand, a hundred thousand — the numbers climb every season while the physics underneath barely changes. The real limitation in a hand-held IPL or laser hair removal unit is not how many flashes the capacitor can deliver. It is how much of each flash actually lands on the skin.
That is the argument for the VCSEL 2835 laser LED at 660 nm / 940 nm — a vertical-cavity surface-emitting laser in a 2.8 × 3.5 mm SMD outline, with a 28° beam instead of the 120° wash of a standard LED.
Why 28 Degrees Changes The Whole Handpiece
A conventional 2835 LED spreads light across roughly 120°. Inside a handpiece with a 10 × 20 mm treatment window, most of that output bounces off the reflector or lands outside the window entirely. The VCSEL part puts the same optical power into a 28° cone, so the window receives a far higher share of every pulse — which shows up as either a shorter treatment time or a lower drive current for the same result.
Because a VCSEL emits from the surface rather than from a cleaved edge, it also behaves like an SMD component: reflow solderable, no facet to damage, no can package, and no alignment step in assembly. For a device maker moving from a laser diode module to a board-level part, that removes an entire mechanical sub-assembly.
Three Application Scenarios Where This Part Fits
- Home IPL and hair removal handpieces — 660 nm visible red for the treatment window and pilot beam, 940 nm for the invisible working beam that does the heating.
- Freckle and skin-tone handpieces — short, narrow pulses that concentrate energy on pigment instead of spreading it across the surrounding skin.
- Night-vision illumination, laser ranging and machine vision — 940 nm stays invisible to the eye for surveillance, drones and pose recognition, while the 28° cone throws useful light much further than a wide LED beam.
Technical Snapshot: VCSEL 2835 Laser LED
| Parameter |
660 nm |
940 nm |
| Radiant power Iv |
15 mW |
20 mW |
| Dominant wavelength |
650–665 nm |
935–945 nm |
| Forward voltage VF |
2.0–2.4 V |
1.8–2.2 V |
| Beam / test current |
28° viewing angle at 20 mA — a narrow, collimated cone |
| Package |
2835 SMD, 99.99% gold wire bonding, 50,000 h rated life |
| Compliance |
RoHS and REACH, instant light under 100 ns, lead-free reflow |
Three Rules Before You Design It In
- Treat the beam, not the lumen figure, as the design target. With a 28° cone, a small shift in the distance between lens and window changes the power density a lot — fix the optics stack before you fix the drive current.
- Ask for the divergence and power bin together. Two reels can meet the same wavelength spec and still deliver different power density at the skin; matched bins keep handpieces consistent from unit to unit.
- Design the safety layer as part of the light path. A collimated source needs the diffuser, skin-contact interlock and window design working together, not a diffuser added at the end of the project.
Buyer check: if a handpiece spec quotes treatment energy but never mentions beam angle, ask for the optical path drawing. Energy per pulse means very little until the cone angle and the window area are on the same page.
Where To Source This Part
Dongguan Lanjin Optoelectronics Co., Ltd. has built SMD LEDs, through-hole LEDs, LED displays and LED PCB assemblies since 2005 from a 2,500 m² anti-static workshop, with ISO9001:2015 certification, two national invention patents and twelve utility model patents. For laser and infrared parts the practical advantages are power and wavelength binning to the handpiece design, small reels for pilot builds, and PCB assembly in the same plant — so an optical complaint and a corrected lot stay in one loop.
Designing an IPL, hair removal or night-vision device? Send the treatment window size, target power density and wavelength — the VCSEL 2835 can be binned to the handpiece you already have instead of forcing a mechanical redesign.
پیام شما باید بین 20 تا 3000 کاراکتر باشد!
Persian
